All GT06N SMS Commands (GT06N Command List)
| No. | Function | Command | Reply |
| QUERY CLASS | |||
| 1 | Check firmware version | VERSION# | e.g.[VERSION]GT06B_10_8MM_B25_V11_LA [BUILD]2013/01/04 17:45 |
| 2 | Check parameters | PARAM# | e.g. GPS report on time interval： IMEI:868120103643505;TIMER:20,20; SENDS:5; SOS:13730454825,,; Center Number:;Sensorset:10,1,5,1; Defense time:10; TimeZone:E,8,0; GPS report on distance interval： IMEI:868120103643505;Distance:200; SENDS:5; SOS:13730454825,,; Center Number:;Sensorset:10,1,5,1; Defense time:10; TimeZone:E,8,0; |
| 3 | Query device network setting | GPRSSET# | e.g.GPRS:ON; APN:CMNET,,; Server:1,hgt06.szdatasource.com,8841,0; URL:http://maps.google.com/maps?q=; |
| 4 | Check status | STATUS# | e.g.Battery:3.41V,Battery too low! Warning; GPRS:Link Up; GSM Signal Level:Strong; GPS:Successful positioning, SVS Used in fix:10(11), GPS Signal Level:32,31,32,31,28,29,29,36,32,33; ACC:OFF; Defense:OFF |
| 5 | Check position status | WHERE# | e.g.Current position! Lat:N22.577156,Lon:E113.916748,Course:0.00,Speed:0.00Km/h,Date Time:2013-01-08 17:35:32 |
| 6 | Check URL | URL# | e.g.<01-08 17:36>http://maps.google.com/maps?q=N22.577156,E113.916748 |
| 7 | Check position | POSITION# OR 123 | e.g. GPS located: <01-08 17:36>http://maps.google.com/maps?q=N22.577156,E113.916748 GPS not located: GPS not fixed, please wait for a while, and then try again. |
| 8 | Check geo fence status | FENCE# | e.g.FenceType:Circle, ON, Latitude:N22.577091, Longitude:E113.916748, radius:600m, in out:IN or OUT, alarm type:1 FenceType:Circle, OFF, Latitude:0.000000, Longitude:0.000000, radius:0m, in out:IN or OUT, alarm type:1 |
| 9 | Check moving status | MOVING# | e.g.Moving Switch:OFF; Radius:300m; Alarm type:1 Moving Switch:ON; Lat:N22.577080; Lon:E113.916794; Radius:300m; Alarm type:1 |
| No. | Function | Command | Explanation |
| SETTING CLASS | |||
| 1 | Set APN | APN, [apnname]# OR APN, [apnname],[user],[pwd]# | Close automatic APN and set by yourself. |
| APN# | Check the current APN parameters. | ||
| 3 | Set server parameters | SERVER,mode,domainName/IP,port,protocol | eg: SERVER,1,www.ydpat.com,8011,0# SERVER,0,211.154.135.113,8011,0# mode = 1 means set with domain name mode = 0 means set with ip address protocol = 0 means connect server with TCP protocol protocol = 1 means connect server with UDP protocol |
| SERVER# | Check the current sever parameters | ||
| 7 | GPRS switch | GPRSON,X# | X=0 or 1;"1" means GPRS ON, "0" means GPRS OFF, default:1 |
| GPRSON# | Check the current GPRS status | ||
| 8 | Reboot | RESET# | The device would reboot in 20S after receiving the command. |
| 9 | GPRS blocking alarm | GPRSALM,X# | X=ON/OFF, default: OFF |
| GPRSALM# | Check the GPRS alarm status | ||
| 10 | SOS setting | SOS,A,[phone number 1][,phone number 2][,phone number 3]# | Add SOS phone number. |
| SOS,D,[sequence number 1][, sequence number 2][,sequence number 3]# | Delete the phone number according to the sequence number. | ||
| SOS,[D],[phone number]# | Delete the matching SOS phone number. | ||
| SOS# | Check the SOS phone number. | ||
| 11 | Center phone number setting | CENTER, A,[phone number]# | Add center phone number. |
| CENTER, D# | Delete center phone number. | ||
| CENTER# | Check the center phone number. | ||
| 13 | Set GPS data sending interval | TIMER,[T1],[T2]# | T1 ranges 5~18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 10; T2 ranges 5~18000 (seconds), upload interval when ACC OFF, default is 10; |
| TIMER# | Check the current parameters of T1 and T2. | ||
| 14 | Set distance interval of GPS data sending | DISTANCE,[D]# | D ranges 50~10000 or 0(meters), distance interval, default is 300; |
| DISTANCE# | Check the current distance interval. | ||
| 16 | Set the upload for ACC status change | ACCREP,[A]# | A=ON/OFF, upload for ACC status change, default: ON |
| ACCREP# | Check the upload for ACC status change. | ||
| 17 | Set the GPS data sending batch | BATCH,[A][,N]# | A= A=ON/OFF, data sending batch function on or off, default:OFF N=1～50, N means the number of messages in the batch, default：10； |
| BATCH# | Check the number of messages in a batch. | ||
| 18 | Set the delay of the defense | DEFENSE,[A]# | A= 1～60 (minute), delay of the defense, default：10 (minutes). |
| DEFENSE# | Check the parameters of the defense. | ||
| 19 | Set vibration sensor detecting time | SENSOR,<A>,[,B][,C]# | A=10-300 seconds,detecting time. Default: 10 seconds B-10-300 seconds, alert delay. Deault:180 seconds C=1-3000 minutes, vibration alert interval. Default: 30 minutes SENSOR# Check the parameter of the status |
| 24 | Set the petrol/electricity control | RELAY,[A]# | A=0/1；0 means connection, 1 means cut off；default: 0. |
| RELAY# | Check the status of the control. | ||
| 25 | Set delay time of voice monitor | DELAY,<A># | A=0、5-18 seconds; Default: 10 seconds (Enter Listen-In after 10 senconds calling) |
| 26 | Set the fence alarm | FENCE,[B],0,[D],[E],[F],[X],[M]# | circle area; B=ON/OFF, open or close fence alarm, default：close; D=the latitude of the circle center; E=the longitude of the circle center; F=1～9999, the fence radius, unit：100 meters; X=IN/OUT；IN: alarming when get in the fence, OUT: alarming when get out the fence, blank means both alarming when get in or get out the fence, default: blank. M=0/1；way of alarming, 0：GPRS only, 1：SMS+GPRS, default：1 |
| FENCE,[B],1,[D],[E],[F],[G][,X][,M]# | rectangle area B=ON/OFF, open or close fence alarm, default：close; D=the latitude of the position 1；range：-90 ～90(degree)； E=the longitude of the position 1；range：-180 ～180(degree)； F=the latitude of the position 2；range：-90 ～90(degree)； G=the longitude of the position 2；range：-180 ～180(degree)； the latitude supports "N/S" or "+/- " coming before it's value； the longitude supports "E/W" or "+/- " coming before it's value；； | ||
| FENCE# | Check the parameters of the fence. | ||
| 27 | Set the vibration alarm | SENALM,[A][,M]# | A=ON/OFF, default: OFF; M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS+GPRS, 2 : GPRS+SMS+phone call, default:1 |
| SENALM,OFF# | Close vibration alarm | ||
| SENALM# | Check the parameters of the alarm | ||
| 28 | Set the power cut-off alarm | POWERALM, [A][,M][,T1][,T2]# | A=ON/OFF, default：ON; M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2 : GPRS+SMS+phone call, default：1； T1=2～60 (second), default：5； T2=1～3600 (second), default：300； |
| POWERALM, OFF# | Close the power alarm. | ||
| POWERALM # | Check the parameters of the alarm. | ||
| 29 | Set the low battery alarm | BATALM, [A][, M]# | A=ON/OFF, default：ON; M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2 : GPRS+SMS+phone call, default：1； |
| BATALM,OFF# | Close the low battery alarm. | ||
| BATALM# | Check the parameters of the alarm. | ||
| 30 | Set the SOS alarm | SOSALM,[A],[M]# | A=ON/OFF, default：ON; M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS+GPRS, 2 : GPRS+SMS+phone call, default：1； |
| SOSALM,OFF# | Close the SOS alarm. | ||
| SOSALM# | Check the parameters of the alarm. | ||
| 31 | Set the dialing times | CALL,N# | N=1～3, default：3, times to dial all numbers; |
| CALL# | Check the parameters of the dialing. | ||
| 32 | Set the moving alarm | MOVING,[A][,R][,M]# | A=ON/OFF, default：OFF; R=100～1000, moving radius, unit: meter, default: 300； M=0～2, 0: GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default：1； |
| MOVING,OFF# | Close the moving alarm. | ||
| MOVING# | Check the status and the parameters of the moving alarm. | ||
| 33 | Set the overspeed alarm | SPEED,[A][,B][,C][,M]# | A=ON/OFF, open or close over speed alarm, default：OFF B=5～600 (second), time interval, default：20 (second) C=1～255(km/h), speed limit, default：100(km/h); M=0/1, way of alarm, 0 : GPRS only, 1: SMS+GPRS, default：1. |
| SPEED# | Check the parameters of over speed. | ||
| 35 | Set the LED sleep mode | LEDSLEEP,[A]# | A=ON/OFF, LED sleep mode control, ON: start LED sleep mode, OFF:LED normal display, default：ON； |
| LEDSLEEP# | Check the parameters of LED sleep mode. |
Post a Comment